I have to issues that may or may not be related.I have a cx3-10c with 2 enclosures attached to it. We purchased a third enclosure from the documents I read this model can have 4 enclosures and up to 60 drives attached.
When you added the new shelf, did you configure the shelf via the buttons on the back before you connected it, or did you just connect it? If you just connected it, remove it ASAP and get the array back into a correctly setup state.Then you'll need to correctly set the shelf ID and then reconnect the shelf.DennyMVPMCSA (2003) / MCDBA (SQL 2000)MCTS (SQL 2005 / SQL 2005 BI / SQL 2008 DBA / SQL 2008 DBD / SQL 2008 BI / MWSS 3.0: Configuration / MOSS 2007: Configuration)MCITP (SQL 2005 DBA / SQL 2008 DBA / SQL 2005 DBD / SQL 2008 DBD / SQL 2005 BI / SQL 2008 BI)RE: EMC cx3-10c adding addition enclosure (TechnicalUser).
At first no, the enclosure ID was not changed and there was different message, we then unplugged it and changed the ID, then it would not reconnect after having the correct ID.This morning we got it all working by restarting everything, and the 3rd enclosure is now visable however we are no receiving an error message when we try to bring the 3rd enclosure online:'The system already contains the maximum number of DAEs (0DAEs). This DAE cannot be brought online.'
RE: EMC cx3-10c adding addition enclosure (Programmer) 17 Jan 11 17:08. That isn't the info that that I was looking for. There's a command that will dump all the info but I haven't used it in a while. Give getall a try. If the output is massive that's the one that we are looking for.DennyMVPMCSA (2003) / MCDBA (SQL 2000)MCTS (SQL 2005 / SQL 2005 BI / SQL 2008 DBA / SQL 2008 DBD / SQL 2008 BI / MWSS 3.0: Configuration / MOSS 2007: Configuration)MCITP (SQL 2005 DBA / SQL 2008 DBA / SQL 2005 DBD / SQL 2008 DBD / SQL 2005 BI / SQL 2008 BI)RE: EMC cx3-10c adding addition enclosure (TechnicalUser). Below is the output of the getall. Bus 0 Enclosure 2 is the one that I am trying to bring online.
9 June 2019 ILAC, the international organisation for accreditation bodies, says: '9 June 2019 marks World Accreditation Day as a global initiative, jointly established by the International Accreditation Forum (IAF) and the International Laboratory Accreditation Cooperation (ILAC), to raise awareness of the importance of accreditation. 305 TPI to 350 TPI Conversion. If you are looking to convert your car from a 305 TPI to a 350 TPI setup, then you should find the information below rather useful.
I wonder if the problem is because the shelf is connected to bus 0. Have you tried connecting it as bus 1 shelf 0? The array may expect that the shelves are balanced across both shelves.DennyMVPMCSA (2003) / MCDBA (SQL 2000)MCTS (SQL 2005 / SQL 2005 BI / SQL 2008 DBA / SQL 2008 DBD / SQL 2008 BI / MWSS 3.0: Configuration / MOSS 2007: Configuration)MCITP (SQL 2005 DBA / SQL 2008 DBA / SQL 2005 DBD / SQL 2008 DBD / SQL 2005 BI / SQL 2008 BI)RE: EMC cx3-10c adding addition enclosure (TechnicalUser). So I noticed that not only was the enclosure in a fault state but when i looked at the enclosure each of the drives also had a green and amber light on them.I then decided to remove all of the drives and the fault on the array went away.
![Emc Zeromark 69704 Emc Zeromark 69704](/uploads/1/2/4/6/124696447/209005103.png)
I still received the message 'The system already contains the maximum number of DAEs (0DAEs). This DAE cannot be brought online.' Once i inserted a drive again then the enclosure faulted again.Not sure if that gives you any other ideas or not.thank you RE: EMC cx3-10c adding addition enclosure (Programmer) 20 Jan 11 13:15.